Denbigh Driveway Gate

The Denbigh driveway gates are a timeless classic and will turn your neighbours green with envy.

This simple, yet stunning, design would look beautiful on any driveway and add a wow factor to any home.

These gates are made by our time served craftsmen specifically to fit your measurements.

Online prices from 900mm to 2100 in height & opening widths from 1600mm upto 4000mm. For any sizes outside these please contact us.

For gate width we require the overall combined (two gate) widths.

Want to use imperial instead of metric? Use our converter here

Enter your required gate height in mm, usually you will allow 50mm / 2" clearances under the gates.
Enter your overall opening width either between brickwork (or similar) opening or between posts. If you require posts these can be added later.
Scandinavian Redwood (+...)
Meranti (+...)
Idigbo Hardwood (+...)
A1 Accoya (+...)
Prime European Oak (+...)
Please select from our range of timbers
Accoya is priced as suitable for painting, if you intend to stain the timber then please contact us for a price enquiries@woodworkersuk.co.uk.

Prices online are for heights between 900mm to 2100mm high (at highest point) & 1600mm wide to 4000mm wide, for any sizes outside these please contact us at
enquiries@woodworkersuk.co.uk for a personalised costing.
Curved joggles to give the gates strength
Curved (Standard)
Pyramid joggles to give the gates strength
Pyramid
Angled joggles to give the gates strength
Angled
Rounded joggles to give the gates strength
Rounded (+£24.00)
Inverted joggles to give the gates strength
Inverted (+£24.00)
Birdsmouth joggles to give the gates strength
Birdsmouth (+£48.00)
Joggles are the protrusions on top corners of the gates, these give the mortice & tenon joints strength. As standard the joggles are arched/curved.
Optional cover strip sits over the 10mm clearance gap between the two gates in the centre.
50/50 split is where both gates of the pair are the same size. Unequally split gives you one gate larger than the other so one gate can be used as a pedestrian access gate.
Maximum width of a single gate is 2000mm. Please state preferred width of gates for split. For example if total width is 3000mm, you can state 1000mm and 2000mm.
Which gate is the smaller gate when viewed from the front? Left or Right.
Example of the open boarding within a gate
Open Boarded
Close up of a close boarded / fully boarded section of a gate
Close Boarded
Open boarded or slatted gates are great if you live in a windy area, as they allow the wind to pass through the gates. Larger close boarded gates can be difficult, at times, to open into a strong wind; you run the risk of the wind dragging them out of your hands; with an open boarded gate, this can be greatly reduced.
Usually with a gate, the bracing and rails are exposed on the rear. Choose double boarded/double sided gates if you don't want to see the rails/bracing.
Not recommended however if you are intending to automate the gates.
standard bracing or double braced driveway gates
The rear of the gates has diagonal bracing, this should point down to the bottom rail and spreads the weight to the hinge side. In some instances or if you are automating the gates with an above ground system the you would double brace the gates so the bracing forms an 'X' on the rear of each gate. On shorter gates double bracing willappear as an upturned 'V'.
add a full thickness bottom rail
As standard gates have bottom rail that can only be seen from rear, from the front it is covered by the cladding. Add a full thickness bottom rails means the bottom rail can be seen from both sides of the gates, bottom rail being 5 3/4" / 145mm tall with the cladding being jointed into the rail. Bottom rail is required if you intend to automate the gates with a below ground automation system.
Fixing stile options
Posts for fixing to a wall or other structure. Priced per stile. Supplied in same timber as your gates.
Posts for fixing to a wall or other structure. Priced per stile.( 95mm x 70mm with 20mm x 20mm loose stop) supplied in same timber as your gates.
4 way weather cut softwood posts
100mm x 100mm (+£54.00)
4 way weather cut softwood posts
125mm x 125mm (+£79.20)
4 way weather cut softwood posts
150mm x 150mm (+£112.80)
square tanalised softwood posts
175mm x 175mm (+£163.20)
square tanalised softwood posts
200mm x 200mm (+£187.20)
All priced per post. As a rule of thumb post size should be for every 12" (300mm) of gate, posts should be 1" (25mm) + 1" (25mm). Posts upto 150mm / 6" square are 4 way weather cut on top. Posts over this are square cut. I.E. 4ft (1220mm gate) should have a 125mm / 5" post
Ironmongery options for driveway gates
Ironmongery packs for your driveway gates. All packs contains 2 Pair 18" Adjustable gate hinges, 2 x 18" Dropbolts & 1 x 6" Ringlatch. All fixings included.
Ironmongery packs for your driveway gates. All packs contains 3 Pair 18" Adjustable gate hinges, 2 x 18" Dropbolts & 1 x 6" Ringlatch. All fixings included.
Ironmongery packs for your driveway gates. All packs contains 2 Pair 24" Adjustable gate hinges, 2 x 18" Dropbolts & 1 x 6" Ringlatch. All fixings included.
Ironmongery packs for your driveway gates. All packs contains 3 Pair 24" Adjustable gate hinges, 2 x 18" Dropbolts & 1 x 6" Ringlatch. All fixings included.
Ironmongery packs for your driveway gates. All packs contains 2 Pair 36" Adjustable gate hinges, 2 x 18" Dropbolts & 1 x 6" Ringlatch. All fixings included.
Ironmongery packs for your driveway gates. All packs contains 3 Pair 36" Adjustable gate hinges, 2 x 18" Dropbolts & 1 x 6" Ringlatch. All fixings included.
200mm / 8" Black Brenton Padbolt
8" Black Brenton Padbolt (+£3.26)
200mm / 8" galvanised Brenton Padbolt
8" Galvanised Brenton Padbolt (+£3.60)
200mm / 8" Black on galvanised Brenton Padbolt
200mm/8" Black over Galv Brenton Padbolt (+£13.20)
200mm / 8" Marine Grade Stainless Steel Padbolt
8" Marine Grade Stainless Steel Brenton Padbolt (+£34.80)
Union Strongbolt 5 Lever insurance deadlock brass finish
Union 5 lever Insurance Deadlock (Brass coloured finish) (+£28.80)
Union Strongbolt 5 Lever insurance deadlock chrome finish
Union 5 lever Insurance Deadlock (Chromecoloured finish) (+£28.80)
Easi T 5 Lever insurance deadlock stainless steel
Easi T Stainless Steel 5 Lever Insurance deadlock (+£37.20)
Perry 70mm Double locking long throw gate lock
Perry 70mm Double locking long throw lock (+£44.40)
Perry 70mm Single locking long throw gate lock
Perry 70mm Single locking long throw lock (+£42.00)
Select your choice of locks if required. Mortice deadlocks are the most secure and operated by key from either side. Brenton Padbolts are lockable by way of a padlock (not supplied) and the Long throw locks fit to (usually the rear) of the gates, doube locking is key operated from either side, single locking is key operated from front, with latch on rear to unlock.
Any additional details you think might be relevant to help us manufacture your gates.
Grand total
Current lead times are approx 8-10 weeks at present

Description

The Denbigh driveway gates are a timeless classic.

This simple, yet stunning, design would look beautiful on any driveway and add a wow factor to any home.

If you want to turn your neighbours green with envy, the Denbigh gates are sure to do it.

These gates are made by our time served craftsmen specifically to fit your measurements.

The gate is based on our tried and trusted wedged morticed and tenon solid frame and supplied either fully close boarded as shown or as an open boarded gate.

Want to fit the Denbigh driveway gates into an enclosed opening?

Want to get rid of the joggles (horn like protrusions) at the top of the gates? You can read more on this over on our Denbigh pedestrian gate page.

We can supply our Denbigh driveway gates without the protruding joggles if you intend to fit the gates within an enclosed brickwork opening.

Denbigh driveway gates – specifications

All top edges on any horizontal rails of the Denbigh feature an angled water run off, this stops the build up of moisture on your gates and makes for a longer lifespan. The stiles of the Denbigh driveway gate (vertical outer uprights of the gate frame) also have rounded outer edges.

Automation – Can be automated, please contact us for details
Construction – Through wedged, morticed & tenoned jointed frame
Height – Made to measure
Width – Made to Measure
Stiles – 2 3/4″ x 2 3/4″ / 70mm x 70mm
Top rail/Head – 2 3/4″ x 2 3/4″ / 70mm x 70mm
Hidden rails (visible from rear only) – 2 3/4″ x 1 7/8″ / 70mm x 48mm
Boarding – 3 3/4″ x 5/8″ / 95mm x 15mm

Available in the following timbers –

Prime European Oak (Hardwood),
Accoya (Modified Softwood),
Idigbo (Hardwood),
Meranti (Hardwood),
Scandinavian Redwood (Softwood)

Our Guarantee

Gate Expectation’s mission is to bring the highest quality bespoke measured wooden gates, side hung wooden garage doors and general joinery items to the market at a quality and price point that can’t be matched.

If not completely satisfied we offer 30-day no hassle returns on all our off-the-shelf range.

Three generations of master carpentry and joinery experience in each and every product. Read more about our history here.

Imperial Converter